Robot Costume Hack

Solar botics
October 24, 2016

img_20161011_105711

Since Halloween is just around the corner we've built and published a few projects in order to give some ideas to the DIY costume-inclined folks. One is DIY Halloween RGB LED Kitty Ears and two is Halloween LED Witch Hat.

So for this third hack we started with an online-bought robot costume, but being a creative tech people, we couldn't resist making it better by using some brilliant LED strips that react to sound.

Supplies used:

The Teensy was chosen because it has hardware based Fast-Fourier-Transform optimizations, and lots of memory.

The dense LEDs (144 per meter) were used on the helmet. More spaced apart (30 per meter) were used on the arms. All of them drive from one Teensy receiving analog signal from the microphone located in the helmet. The microphone captures both the voice of the wearer and ambient sounds.

Here's what it looks like reacting to the music:

Technical Build:

The idea was to attach two denser LED strips to the face mask guard and the rest to the arms of the costume. They both would react to ambient sound and light up depending on the frequency of sound. The helmet's strip would have the lower frequencies in the middle and the arms would have them start at the wrists.

The face mask guard took 52 LEDs per strip and arms got 25 LEDs per arm. These calculations are reflected in the code below.

For the arms, I divided each LED strip into two sections (since the costume itself had separate foam pieces for forearm and shoulder), and gave them their own battery.  That allowed me to have a simple 2 pin connection for joining the arms to the helmet.

img_0880

One problem when dealing with RGB Strips on wearables is that the solder pads are small and the wires break off too easily.  I tried to minimize this by adhering a small wooden backing to the end of each strip.  This acts like a cast and, when sealed with heat shrink, immobilizes the connections.  I cut the supports on the laser cutter, but you can use anything.  Popsicle sticks would work as well.

img_08341

Here is the basic wiring diagram I used:

 Wiring for Robot Costume
Wiring for Robot Costume

Software:

This code uses hardware support for FFT that's built into the Teensy.  If you want to use a different processor, you will need to add a FFT library and modify the code accordingly.

I found some code online that was almost perfect for this project. Rather than reinventing the wheel, I reused that code, and modified it for my needs.  Original credit has been left in the code.

Robot Costume Code

Summary:

With Halloween just around the corner, this costume should be a hit at any event.. I can't wait to wear it!

14963128_682570741900621_487933391291499477_n

photo credit Lucky Shot (David Luckman)

MORE POSTS

August 8, 2017
Project: LED Earrings

The idea of adorning oneself with glowing bits has been around forever, but instead of smearing ourselves with phosphorescent jellyfish or placing fireflies in ears like some uncivilized cavemen we went for simple LED earrings. We made a build that involves a simple slow-scroll RGB LED and a few reflective bits to bounce that pretty […]

January 4, 2016
Monday New Product: Filament & Tiny...

#4-40x1/2in Yellow Zinc Standoff, M/M, 1/4in threaded ends $0.50 #4-40 x 1/2" yellow zinc coated (chromate) steel standoff. IR Reflector sensor with leads $1.00 Reflective optical sensor with transistor output. 44mm Piezo Speaker $2.25 For making a LOUD beep, this piezo suits your need. Comes mounted in a plastic case with mounting tabs. Maxell LR44 […]

March 21, 2018
Project: Experiments in Watermelon Filam...

It takes a while to get to know all the quirks of your 3D printer and filament well. We thought we'd add to the knowledge base and share what we've learned about using the eSun 1.75mm PLA filament in Glass Watermelon Red on our Kossel Pro delta style 3D printer.

July 28, 2005
RoboSapien Movie

Hi all. Yesterday's solar race cars were very cool. Lots of neat tech, and a neck'n'neck race to the finish too! I took the extra effort to see some of the cars out at highway speed, then saw them again in-town. These things move! Anyways, enough about that. I got an email from John Hopkins, […]

Solarbotics Ltd Logo
Solarbotics has been operating for more than 25 years, bringing electronics know-how and supplies to both the electronics professional and hobbyist. We'll be happy to help you too!

Solarbotics, Ltd. is not responsible for misprints or errors on product prices or information. For more information, please see our Terms and Conditions.

Warning: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Please visit www.P65Warnings.ca.gov for more information. This item was manufactured prior to August 31, 2018.

cart