Robot Costume Hack

Solar botics
October 24, 2016

img_20161011_105711

Since Halloween is just around the corner we've built and published a few projects in order to give some ideas to the DIY costume-inclined folks. One is DIY Halloween RGB LED Kitty Ears and two is Halloween LED Witch Hat.

So for this third hack we started with an online-bought robot costume, but being a creative tech people, we couldn't resist making it better by using some brilliant LED strips that react to sound.

Supplies used:

The Teensy was chosen because it has hardware based Fast-Fourier-Transform optimizations, and lots of memory.

The dense LEDs (144 per meter) were used on the helmet. More spaced apart (30 per meter) were used on the arms. All of them drive from one Teensy receiving analog signal from the microphone located in the helmet. The microphone captures both the voice of the wearer and ambient sounds.

Here's what it looks like reacting to the music:

Technical Build:

The idea was to attach two denser LED strips to the face mask guard and the rest to the arms of the costume. They both would react to ambient sound and light up depending on the frequency of sound. The helmet's strip would have the lower frequencies in the middle and the arms would have them start at the wrists.

The face mask guard took 52 LEDs per strip and arms got 25 LEDs per arm. These calculations are reflected in the code below.

For the arms, I divided each LED strip into two sections (since the costume itself had separate foam pieces for forearm and shoulder), and gave them their own battery.  That allowed me to have a simple 2 pin connection for joining the arms to the helmet.

img_0880

One problem when dealing with RGB Strips on wearables is that the solder pads are small and the wires break off too easily.  I tried to minimize this by adhering a small wooden backing to the end of each strip.  This acts like a cast and, when sealed with heat shrink, immobilizes the connections.  I cut the supports on the laser cutter, but you can use anything.  Popsicle sticks would work as well.

img_08341

Here is the basic wiring diagram I used:

 Wiring for Robot Costume
Wiring for Robot Costume

Software:

This code uses hardware support for FFT that's built into the Teensy.  If you want to use a different processor, you will need to add a FFT library and modify the code accordingly.

I found some code online that was almost perfect for this project. Rather than reinventing the wheel, I reused that code, and modified it for my needs.  Original credit has been left in the code.

Robot Costume Code

Summary:

With Halloween just around the corner, this costume should be a hit at any event.. I can't wait to wear it!

14963128_682570741900621_487933391291499477_n

photo credit Lucky Shot (David Luckman)

MORE POSTS

February 23, 2018
APA102-2020 MicroNova Custom LED Choker

I created this choker as a project to demonstrate the new MicroNova APA102-2020 LED strips. Photo by Yeti, edited by Batgirl These addressable LEDs are extremely small, less than 1/4 the size of a standard 5050 LED. This project was built using engineering sample standard MicroNova 99 LED / meter strips . The MicroNova strips we are selling have 198/meter - […]

December 23, 2004
Solarbotics Holiday Schedule

Solarbotics will be slightly altering our holiday hours to enable staff to spend time with friends & family. We will be closed Friday, December 24th to Tuesday, December 28th and Friday, December the 31st. On Monday, January 3rd, 2005 we will resume our normal hours, 9:00am - 6:00pm MST. Solarbotics wishes all the best to […]

October 24, 2014
Friday New Product: Trinkets, Addressabl...

Today is the auspicious day of October 24. It is so important I can't stop thinking about it even when I am preparing my taxes. Wikipedia mentions is as a the Day of All New Products. It is celebrated as a state holiday in Namibia, where it is also known as the day of jackalope. […]

August 11, 2012
New Products: LED Strips, LED Controller...

Hello everyone, today I'll be your guest Russian host. Here's your new product, look at it and leave me alone! I'm busy eating vodka and drinking borscht. In the dacha. After the banya. (Is that good enough for Russian stereotypes?) Right about now the most observant of you might notice that something is wrong with […]

1 2 3 252
Solarbotics Ltd Logo
Solarbotics has been operating for more than 25 years, bringing electronics know-how and supplies to both the electronics professional and hobbyist. We'll be happy to help you too!

Solarbotics, Ltd. is not responsible for misprints or errors on product prices or information. For more information, please see our Terms and Conditions.

Warning: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Please visit www.P65Warnings.ca.gov for more information. This item was manufactured prior to August 31, 2018.

Copyright © 2024 Solarbotics Ltd. All Rights Reserved
This is a block of text. Double-click this text to edit it.
cart