Chug-O-Meter Celebrating Arduino Day �...

Dave Hrynkiw
March 13, 2019

Isn’t it nice when you can hit two birds with one stone?

That’s exactly what we’ve done as we approach both Arduino Day and Saint Patrick’s Day with our version of the Chug-O-Meter!

We absolutely loved what the circuit.io team did with their Chug Meter but thought that we could add more to its survivability while surrounded by inebriated merrymakers. To do this we changed the force sensor to regular switches, created a 3D printed abs enclosure, and then placed the electronics inside the enclosure to keep them away from accidental spills and splashes.

Step 1: Gathering the Parts

Parts

It can be awesome working at an electronics company when you want to design and build a project. For the Chug-O-Meter, we dived into our stock and found several components that will fit the build.

· 1x DC-DC Boost Converter Power Supply Module (40408)

· 1x CR2032 Coil Cell Holder (50484)

· 1x CR2032 Lithium Battery (BattC2032)

· 1x Power Switch (SWT1A)

· 3x Snap Lever Switch (SWT9)

· 1x 7-Segment Serial Display (50424)

· 6x #2-56 1/2” Thread Forming Screw (Not carried as Solarbotics)

· 2x M3 x 10mm Machine Screw (M3x10-PPH)

· 1x Roll of your favorite 3D Printer Filament. We used eSun ABS+ White (60801)

· 1x 10k Resistor (R10k)

· 1x 0.1uF Capacitor (CP0.1uF)

· 2x colors of Groovy Noodle Wire (15060)

· 1x double sided tape or hot glue

Tools

One thing you may have noticed in the parts list is that we haven’t included an Arduino! Weird, huh? Well that’s because of SparkFun's 7-Segment Serial Display is actually an Arduino in and of itself! Because of this, we’ve overwritten the code used to control the display with regular Arduino code that will control the Chug-O-Meter instead. To do this though, we will need a serial programmer and interface header to do the job.

· 1x TTLyFTDI USB-to-TTL Adapter (39240)

· 1x Male Strip pins 6 pos (MPin6RA)

Note: During the build process, do not solder the Male Strip Pins to the 7-Segment display as there isn’t enough clearance in the enclosure to allow for it when inserting the display!

Step 2: Starting the Build

To start, we are going to solder together the circuit as shown in the image above. This will allow us to power the circuit, turn it off and on, it senses when a drink is placed or removed, and then display the time on the 7-segment display.

Step 3: Programming the Display

Now that we have the circuit together, it’s time to add the code to the display. The picture above depicts how the header is inserted into the 7-segment display, and instead of soldering, we use the tried and true method of “add some force to hold it in place while you program”! However, before we can program our device, we need to do a few simple things to the Arduino environment to make it 7-segment ready.

1. Download and install the latest version of the Arduino IDE (Arduino IDE)

2. Open Arduino and navigate to File > Preferences and then add the following line to the “Additional Board Manager URLs:” (if you already have the text here, just add a “,” to the end of the existing text and then paste the following line after it)

https://raw.githubusercontent.com/sparkfun/Arduino_Boards/master/IDE_Board_Manager/package_sparkfun_index.json

3. Press the okay button for the preferences menu and then navigate to Tools > Board: > Boards Manager…

4. In the “filter your search…” bar, type “Sparkfun avr”

4. Click the install button from the image above, making sure that you install the most recent version which in our case was 1.1.12.

With the proper board now installed, programming the SparkFun 7-segment is only a few simple steps!

1. Copy the code into a new Arduino project or download our zip file for the project and extract and open the

.ino file.

2. Next Select the appropriate board by going Tools > Boards: >Sparkfun Serial 7-Segment Display

3. Select the Port that the FTDI programmer is connected to by going Tools > Port > COM X

4. Finally, while holding the FTDI programmer to the pins on the 7-segment display, press the upload button to program the display with the Chug-O-Meter code.

Fixing the Whoopsie

During the build process of this project, we realized too late that the analog pin that the buttons used to sense the addition/removal of a drink does not have an internal pull-up resistor or debouncing capacitor. To fix this issue, we went ahead and added one ourselves to fix this issue, we recommend that you do the same!

Step 4: Finishing the Build

Now that the display has been programmed and the circuit is complete, it’s time to add the electronics to the enclosure.

1. Double-sided tape or hot glue the electronics as shown so that none of them extend past the top of the enclosure. This will keep them in place and stop any collisions with the sensing switches and plate

2. Screw in the switches as shown using the #2-56 thread forming screws. If you don’t have these, you can also use hot glue, but they won’t be near as robust.

3. Insert the display into the cavity of the display holder and use gravity to wiggle it into dropping into place so that the display is flush with the outside of the enclosure. Since we were kind of running out of time for elegant solutions, we used some ESD-Safe foam to hold it in place, but you could also use paper or anything else that is non-metallic.

4. Finally, use the #4-40 screws to mount the display holder onto the enclosure. You can now flick the switch to turn on the circuit and add the sensing plate to cover everything up!

Step 5: Using the Chug-O-Meter

The Chug-O-Meter has been programmed to make operation a breeze! Turn it on, place down a full glass of whatever liquid you prefer, remove the glass to start the count and start chugging! Once you’ve finished, place the empty glass on the sensing plate to stop the timer. To reset the device, remove the empty cup and place a fresh, full cup onto the plate. happy chugging!

If you like building our kit, send us a photo of your build via email at media@solarbotics.com and we'll feature it!

MORE POSTS

April 26, 2002
Guaranteed Results Workshop at WCRG

Solarbotics is again hosting a Guaranteed Results workshop at the Western Canadian Robot Games, on Friday May 10th, noon to 4pm. It works like this: Pick up any kits from Solarbotics before (or of the day) the workshop, bring it in, and we'll have tools and expertise there to make sure your kit goes together […]

May 25, 2003
Remember the GM5?

Hoped you ordered one while you had the chance - they're all gone now! I will most likely be a looong time before these come back, so please don't contact us asking for more - it was a rare deal for Solarbotics, which we were glad to bring to you for as long as it […]

October 20, 2003
NAIT Robot Challenge

Solarbotics went up to Edmonton, Alberta this last weekend to help out with the Northern Alberta Institute of Technology's Sumovore Mini-Sumo workshop/Robot Challenge/Open House, and to show off our wares. Give it a visit! Yes, yes, the Sumovore will be on sale for the first time tomorrow!

September 4, 2001
BIOBugs Update

News from Mr. Tilden: The official unveiling of Hasbro/Wowwee BIOBugs will be September 14, with a huge unleasing of 100 of these critters into the desert of White Sands, New Mexico. Additionally, Mark himself is slated to be on the Rosie O'Donnell Show sometimes on the week of September 17. This will coincide with the […]

1 2 3 252
Solarbotics Ltd Logo
Solarbotics has been operating for more than 25 years, bringing electronics know-how and supplies to both the electronics professional and hobbyist. We'll be happy to help you too!

Solarbotics, Ltd. is not responsible for misprints or errors on product prices or information. For more information, please see our Terms and Conditions.

Warning: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Please visit www.P65Warnings.ca.gov for more information. This item was manufactured prior to August 31, 2018.

Copyright © 2024 Solarbotics Ltd. All Rights Reserved
This is a block of text. Double-click this text to edit it.
cart